Hydraulic hoses

Tips and tricks, tools and paint

Topic author
Andyjcbman1
Posts: 9
Joined: Thu Oct 29, 2009 10:50 pm
Real name: Andy Mills
Has thanked: 1 time
Flag: Wales
Contact:

Hydraulic hoses

Post #1 by Andyjcbman1 » Mon Nov 28, 2016 9:43 pm

Hello everyone :wave: I am new to the business of posting so my apologies if I have not quite got this right. I am wanting to enhance some of my model jcbs (mostly 1:35) scale with hydraulic hoses and was also thinking of removing the rear bucket on my Britain's 3c to paint it red. Can anyone offer any help or advice? I would really be grateful for any help or suggestions :)


Jeremy Rowland
Moderator
Posts: 8776
Joined: Sun Aug 05, 2007 8:36 pm
Real name: Jeremy Rowland
Has thanked: 1930 times
Been thanked: 1738 times

Re: Hydraulic hoses

Post #2 by Jeremy Rowland » Mon Nov 28, 2016 9:53 pm

Hi Andy and welcome to CMN :wave: I recall that somebody on here used wire from cheapo pound shop earphones for hydraulic hoses on their models, I would guess that you would fix by using a decent superglue. :thumbup:

Jeremy


Topic author
Andyjcbman1
Posts: 9
Joined: Thu Oct 29, 2009 10:50 pm
Real name: Andy Mills
Has thanked: 1 time
Flag: Wales
Contact:

Re: Hydraulic hoses

Post #3 by Andyjcbman1 » Tue Nov 29, 2016 1:02 am

Thanks Jeremy, good idea. How do I go about removing the bucket to re-paint it? Would like to replicate the same 3c as Julian Carder so will also need the front bucket forks too!


Jeremy Rowland
Moderator
Posts: 8776
Joined: Sun Aug 05, 2007 8:36 pm
Real name: Jeremy Rowland
Has thanked: 1930 times
Been thanked: 1738 times

Re: Hydraulic hoses

Post #4 by Jeremy Rowland » Tue Nov 29, 2016 8:49 am

Andyjcbman1 wrote:Thanks Jeremy, good idea. How do I go about removing the bucket to re-paint it? Would like to replicate the same 3c as Julian Carder so will also need the front bucket forks too!


Just a guess here but most models have rams, buckets, arms etc. held in place by brass rivets so you would need to carefully drill the one side of the rivet off and the pin should drive out okay, you'll need to retain the rivet for its size, measure the diameter with a vernier calliper. When fitting the bucket back on I would purchase a length of silver steel from an engineers merchant and cut new securing pins to length, these will simply slide into place but unlike the rivets will not be secured, this should not hurt as its a model and not a toy.
Other members may have better ideas than this but that's how I would tackle the problem.

Jeremy


topkit
Posts: 810
Joined: Mon Sep 22, 2008 11:55 pm
Real name: David
Location: KENT
Has thanked: 85 times
Been thanked: 183 times
Flag: Great Britain

Re: Hydraulic hoses

Post #5 by topkit » Mon Jan 02, 2017 1:03 pm

If you can find a decent modelling shop one that sells plasticard etc they usually sell brass strip and brass tubing, i have various diameters of brass tubing here. The you drill out you old rivet cut a slightly longer piece of brass tube, then place it back into the bucket on the model using a nice round centre punch on the tube then the same again on the opposite side and you have made your brass rivet (all of those metalwork lessons at school did pay off) i do alot of repairs and a few conversions on conrad and NZG models and thats the way i have always done it. :thumbup:


Return to “Tips and tricks, tools and paint”

Who is online

Users browsing this forum: No registered users and 1 guest