Classic pictures Updated 28/04/2024
-
- Posts: 4072
- Joined: Fri Jul 13, 2007 12:43 am
- Real name: essexpete
- Has thanked: 853 times
- Been thanked: 686 times
Re: Classic pictures Updated 06/09/2020
john wrote:At one time the L62 and L64 were the largest 4 wheel drive machines manufactured in the country
Good to hear from you John.
Which model of L series had the horizontal double chamber silencer on the left side?
I think I caught a glimpse of an early L series in a Northamptonshire yard last year. There were quite a lot of caravans and scrap about and my wife was not keen for me to go back and look!
-
Topic author - Posts: 2975
- Joined: Mon Dec 24, 2007 6:10 pm
- Real name: Steve
- Location: Theale Near Reading Berkshire
- Has thanked: 1248 times
- Been thanked: 1835 times
- Flag:
Re: Classic pictures Updated 13/09/2020
Steve
You do not have the required permissions to view the files attached to this post.
-
- Moderator
- Posts: 8679
- Joined: Sun Aug 05, 2007 8:36 pm
- Real name: Jeremy Rowland
- Has thanked: 1875 times
- Been thanked: 1692 times
Re: Classic pictures Updated 13/09/2020
Is that a Pingon being used as a crane in the first photo? Most unusual, there is a Hymac 580C in the 5th photo down behind the Leyland Constructor cement mixer on its side, bet that was a fun recovery job not!
Jeremy
Jeremy
-
Topic author - Posts: 2975
- Joined: Mon Dec 24, 2007 6:10 pm
- Real name: Steve
- Location: Theale Near Reading Berkshire
- Has thanked: 1248 times
- Been thanked: 1835 times
- Flag:
Re: Classic pictures Updated 13/09/2020
Jeremy Rowland wrote:Is that a Pingon being used as a crane in the first photo? Most unusual, there is a Hymac 580C in the 5th photo down behind the Leyland Constructor cement mixer on its side, bet that was a fun recovery job not!
Jeremy
Yes it is a Pingon Jeremy
-
- Posts: 2358
- Joined: Wed Dec 09, 2009 11:28 pm
- Real name: fred evans
- Has thanked: 1295 times
- Been thanked: 1111 times
- Flag:
Re: Classic pictures Updated 13/09/2020
Hi,
I know it's a bit late, but did anyone notice the hammer on the Hymac 580 in The first pic. in Neversweat's previous post.
It's from before the hydraulic hammer caught on. It is a " BSP, (British Steel Piling)," pneumatic hammer. You can see the 600 cu. ft. compressor required to drive it in the picture too. The air hose can be seen draped over the stonework that's being demolished, it drops into and then back out of the water and up the Hymac boom. It's a long time ago now but if I remember rightly the air hose fittings were 2 or even 2.1/2 in BSP.
The Cardiff Plant Group ran a couple of these in the 1960s and I may well have worked on the one in the pic. which is reminiscent of a job
near Bath in Somerset where I was sent to fix one.
Fred
I know it's a bit late, but did anyone notice the hammer on the Hymac 580 in The first pic. in Neversweat's previous post.
It's from before the hydraulic hammer caught on. It is a " BSP, (British Steel Piling)," pneumatic hammer. You can see the 600 cu. ft. compressor required to drive it in the picture too. The air hose can be seen draped over the stonework that's being demolished, it drops into and then back out of the water and up the Hymac boom. It's a long time ago now but if I remember rightly the air hose fittings were 2 or even 2.1/2 in BSP.
The Cardiff Plant Group ran a couple of these in the 1960s and I may well have worked on the one in the pic. which is reminiscent of a job
near Bath in Somerset where I was sent to fix one.
Fred
-
Topic author - Posts: 2975
- Joined: Mon Dec 24, 2007 6:10 pm
- Real name: Steve
- Location: Theale Near Reading Berkshire
- Has thanked: 1248 times
- Been thanked: 1835 times
- Flag:
Re: Classic pictures Updated 20/09/2020
Steve
You do not have the required permissions to view the files attached to this post.
Who is online
Users browsing this forum: No registered users and 24 guests