Search found 646 matches
- Fri May 03, 2024 9:41 pm
- Forum: Loaders/Backhoes
- Topic: 1984 JCB 3CX - Model 4 297348/P/S
- Replies: 4
- Views: 208
- Flag:
Re: 1984 JCB 3CX - Model 4 297348/P/S
There are two plugs on the rear of the centre axle housing. 32mm socket. Bottom for draining and top one to fill through. Fill til the oil runs out of the top one.You need an oil that is suitable for wet brakes. SUTO 10w30 or SUTO 15w40 or UTTO 10w30. I've had no issues in years with any of these bu...
- Fri Apr 12, 2024 9:31 pm
- Forum: Excavators
- Topic: Early 3cx
- Replies: 1
- Views: 267
- Flag:
Re: Early 3cx
One of the first with the BMC engine...
- Mon Apr 08, 2024 11:24 am
- Forum: Loaders/Backhoes
- Topic: '87 3CX Perking 4.236 Injector Pump Problem
- Replies: 29
- Views: 9687
- Flag:
Re: '87 3CX Perking 4.236 Injector Pump Problem
You're now in the wrong thread Gary. You've asked in this one...
https://www.classicmachinery.net/forum/ ... 9&start=10
https://www.classicmachinery.net/forum/ ... 9&start=10
- Fri Apr 05, 2024 8:57 pm
- Forum: Loaders/Backhoes
- Topic: Starting problem - fuel
- Replies: 12
- Views: 11330
- Flag:
Re: Starting problem - fuel
You mean the filter in the inlet end of the injector pump? Yes you can but need to be very careful doing so. Remove the inlet pipe,then the large plug(15/16'' spanner). Then lift out the spring. You can just about see the top of the filter around the outside of the hole. You need something fine to h...
- Thu Feb 15, 2024 9:11 am
- Forum: Loaders/Backhoes
- Topic: JCB 3cx
- Replies: 12
- Views: 22093
- Flag:
Re: JCB 3cx
The lever needs pushed away (anti clockwise) from you to release the clamps. The rotating part that the vertical rod goes into may need pushed around further with a pry bar or suchlike.
- Fri Feb 09, 2024 1:36 am
- Forum: Loaders/Backhoes
- Topic: 4/98 leyland engine swap between JCB3CMk2 & Mk3?
- Replies: 7
- Views: 1303
- Flag:
Re: 4/98 leyland engine swap between JCB3CMk2 & Mk3?
Yes they are. A few internal differences in the last of the MK3 Powertrain engines but still interchangeable.
- Wed Jan 24, 2024 8:46 am
- Forum: Loaders/Backhoes
- Topic: parts catalog for backhoe MF50B
- Replies: 10
- Views: 2181
- Flag:
Re: parts catalog for backhoe MF50B
But the 65 didn't have a 4.236...
Can't help with the 50B manual but there's a Perkins manual in the forum downloads section.
Can't help with the 50B manual but there's a Perkins manual in the forum downloads section.
- Fri Jan 19, 2024 1:17 am
- Forum: Excavators
- Topic: Jcb 3c
- Replies: 9
- Views: 1648
- Flag:
Re: Jcb 3c
You haven't said which MK of 3C. 1,2 or 3?
The return filter is as below for MK 1 and 2. MK 1 has no door covering it and should be obvious to see.
Bottom picture is of the suction filter for MK 2 and 3. Lie on your back and look up under the step. Don't know if MK 1 has this one or not.
The return filter is as below for MK 1 and 2. MK 1 has no door covering it and should be obvious to see.
Bottom picture is of the suction filter for MK 2 and 3. Lie on your back and look up under the step. Don't know if MK 1 has this one or not.
- Thu Jan 18, 2024 9:10 pm
- Forum: Excavators
- Topic: Jcb 3c
- Replies: 9
- Views: 1648
- Flag:
Re: Jcb 3c
If it's a MK1,I think there's only the big return filter in front of the right hand rear wheel.Might be a suction filter somewhere but I'm not familiar with it. The MK2 will have a suction strainer behind/up under the steps into the cab. Flat plate to come off and the strainer is above it. Also then...
- Tue Jan 16, 2024 8:53 pm
- Forum: Loaders/Backhoes
- Topic: Perkins phaser 1004 in 3cx running bad
- Replies: 38
- Views: 244619
- Flag:
Re: Perkins phaser 1004 in 3cx running bad
The thermostat should be inside the housing directly above the sensor you have circled in green. Your engine should really start instantly without any heat with that particular starter on it. Wonder if your fuel lift pump has become weak?