Search found 96 matches
- Mon May 24, 2021 9:54 pm
- Forum: For sale
- Topic: For sale - JCB 3C Mk2 (4in1)
- Replies: 1
- Views: 2920
For sale - JCB 3C Mk2 (4in1)
For sale is our manual JCB 3C Mk2. We bought the machine in early 2012 for our demolition and self build project which is nearing the end (much to my wife’s pleasure)! The good... 4 in 1 loader with pallet forks full suite of buckets (12", 16", 24", 36" 48") New bucket ram N...
- Sat Apr 24, 2021 9:16 pm
- Forum: Loaders/Backhoes
- Topic: 3C Mk2 dash light query
- Replies: 0
- Views: 3862
3C Mk2 dash light query
Hi folks, my Mk2 round red dash light is not illuminating when the ignition is switched on ( it would normally go out once the engine is cranking).
Is this the battery charge light or oil pressure light?
Cheers
Y
Is this the battery charge light or oil pressure light?
Cheers
Y
- Wed Jul 22, 2015 10:21 pm
- Forum: Loaders/Backhoes
- Topic: JCB 3C2 - Battery
- Replies: 3
- Views: 3201
Re: JCB 3C2 - Battery
Thanks for the replies fellas
- Sun Jul 19, 2015 9:40 pm
- Forum: Loaders/Backhoes
- Topic: JCB 3C2 - Battery
- Replies: 3
- Views: 3201
JCB 3C2 - Battery
My battery has finally given up the ghost. Can any of you good folk recommend a suitable battery for the old girl?
Thanks,
Yozza
Thanks,
Yozza
- Sun Jun 29, 2014 11:10 pm
- Forum: Loaders/Backhoes
- Topic: JCB 3C2 - Half shaft nut size
- Replies: 2
- Views: 2040
JCB 3C2 - Half shaft nut size
Hi folks, I've just seen the post http://www.classicmachinery.net/forum/viewtopic.php?f=5&t=10329 and reminded me of the pool of oil sat below my rear wheels :shock: Do any of you know the nut size holding the half shafts? Do the half shafts easily remove or would they need jacking out? In fact,...
- Wed May 14, 2014 1:18 pm
- Forum: Loaders/Backhoes
- Topic: JCB 3C2 - Rear axle seal questions?
- Replies: 4
- Views: 3040
Re: JCB 3C2 - Rear axle seal questions?
Thanks for the answer. Sounds like a biggish job, I'll keep toping up the gearbox oil.
Cheers,
Yozza
Cheers,
Yozza
- Mon May 12, 2014 10:35 pm
- Forum: Loaders/Backhoes
- Topic: JCB 3C2 - Rear axle seal questions?
- Replies: 4
- Views: 3040
JCB 3C2 - Rear axle seal questions?
Hi folks, My rear axle seals leak like a good un, just had to put 2 gallons of oil back in the box :shock: Do any of you knowledgeable folk know if I can get away with taking the rear wheels off and replacing the seals with no serious dismantling? If so, are these seals listed on fleabay the correct...
- Thu May 01, 2014 1:45 pm
- Forum: Excavators
- Topic: jcb 3c died and wont restart
- Replies: 12
- Views: 5874
Re: jcb 3c died and wont restart
I've been caught out by a dicky fuel gauge. Bled everywhere I can think of and no joy until I remembered there is a bleed on the pump itself. Once the pump is bled she fired like a good un.
- Wed Apr 30, 2014 2:58 pm
- Forum: Excavators
- Topic: Pel Job Sirius Plus - Hydraulic Schematic expert assistance required please
- Replies: 0
- Views: 1437
Pel Job Sirius Plus - Hydraulic Schematic expert assistance required please
Hi folks, I am trying to understand the hydraulic circuit that supplys the pilot oil. Please see attached schematic, the pilot oil valve (E21H) has what appears to be a feed into P1 and P2 from the main valve block regulators supplied by 2 of the hydraulic pumps. (see the pilot oil valve in pel job ...
- Fri Apr 18, 2014 11:16 pm
- Forum: Excavators
- Topic: Pel Job 1.5 min digger - slow servos
- Replies: 0
- Views: 1665
Pel Job 1.5 min digger - slow servos
Ay up folks, My builder has a Pel Job mini digger but he as issues with the the hydraulics served by the the servo controls. The blade and tracks respond as soon as the digger starts, but the servo controls take a minute or so before they move the dipper, boom, bucket. Any ideas where the problem ma...